2 loops but on exit continue the first one

[Velnes 0]

how to exit one loop but keep the first loop running.. any1 can help ?

[guinness 1,458]

ExitLoop 1

$Count = 0
$NoSecondLoop = 0
While 1
    While $NoSecondLoop = 0
        Sleep(500)
        $Count += 1
        ConsoleWrite($Count & @CRLF)
        If $Count = 5 Then
            $NoSecondLoop = 1
            ExitLoop 1
;~          ExitLoop 2 Will Exit This Loop And The Second Too.
        EndIf
    WEnd
    ConsoleWrite("First Loop and $Count should be 5 >> " & $Count & @CRLF)
WEnd

Edited March 3, 2011 by guinness

[Velnes 0]

dont work it exits the first loop too...

i am trying to figure out how to exit the second while 1 loop... on $GUI_EVENT_CLOSE and leave first while 1 loop still running until its exited too ((

[iamtheky 729]

$k = 0

while 1
    tooltip ("I am the first constant loop" , 0 , 0)

If $k = 0 Then

for $k = 0 to 10
        msgbox (0 , '' , "I am the second loop, on loop #" & $k & " of 10")
        next
    else
        endif

wend

[guinness 1,458]

Could you post some code please

[Velnes 0]

$GUI = GUICreate("first gui", 250, 600, 812 ,3)
$btn = guictrlcreatebutton("test", 5, 5, 20, 5)
GUISetState(@SW_SHOW)


While 1
    Switch GUIGetMsg()
    Case $GUI_EVENT_CLOSE
        Exit 1
    Case $btn
        _test()
    EndSwitch
WEnd


Func _test()
    $GUI2 = GUICreate("2", 400, 300)
    $test = GUICtrlCreateButton("run test", 5, 25, 100, 20)

    GUISetState(@SW_SHOW)

    

While 1
    Switch GUIGetMsg()
    Case $GUI_EVENT_CLOSE
        ExitLoop 1 ;this dont work.. it closes the first loop also :/
    Case $test
        msgbox(0,"", "testing loop")
    EndSwitch
WEnd

EndFunc

[guinness 1,458]

OK, Maybe best to have a look at the Wiki Entry >> http://www.autoitscript.com/wiki/Managing_Multiple_GUIs

Your Example:

Global $GUI = GUICreate("First GUI", 250, 600, 812, 3)
Global $Button_1 = GUICtrlCreateButton("_Test()", 5, 5, 50, 50)
GUISetState(@SW_SHOW)

While 1
    Switch GUIGetMsg()
        Case -3 ; $GUI_EVENT_CLOSE
            Exit 1
        Case $Button_1
            _Test()
    EndSwitch
WEnd

Func _Test()
    Local $GUI_2 = GUICreate("Second GUI", 400, 300)
    Local $Button_2 = GUICtrlCreateButton("Exit Secon GUI", 5, 25, 100, 20)
    GUISetState(@SW_SHOW)

    While 1
        Switch GUIGetMsg()
            Case -3 ; $GUI_EVENT_CLOSE
                ExitLoop
            Case $Button_2
                MsgBox(0, "", "Second GUI")
                ExitLoop
        EndSwitch
    WEnd
    GUIDelete($GUI_2)
    Return 1
EndFunc   ;==>_Test

It was returning to the previous loop but you had to use GUIDelete()! This is why its always best to post code, otherwise the problem would have taken a little longer

Edited March 3, 2011 by guinness

[Velnes 0]

hehe amn , i first saw the link and not ur code... so i went to read the wiki there on that page u gave... and now i understansd 100%

now i refreshed this page and saw ur edit on my code but didnt need it anymore, but anyway thnx very much for the wiki

realy helpped and works briliat

thnx again

[guinness 1,458]

OK, I had quick 2 minutes to spare! You're Welcome!